Railing Fontanot made to stainless steel Inox21

Railing INOX21 is made from AISI 304 stainless steel with a polished finish. They are characterised by circular-section balusters joined to each other with PMMA anti UV panel with a thickness 8 mm and the steel handrail comes in 150 cm modules.

The baluster, for the installation of the panels, can be installed directly on the floor and are 96 cm high. The balusters to be fastened on the floor also come with plate covers.

INOX21 KIT BASIC is inclusive of all the items necessary for the realization of a railing module.
INOX21 KIT PLUS is inclusive of all the items necessary for the realization of an intermediate section of railing

Warning:
• IINOX21 KIT BASIC and INOX21 KIT PLUS do not contain the PMMA panels, fixing plugs and glue, which must be purchased separately depending on the installation to be made.
• Install the baluster at a distance of less than or equal to 1 m.
• For shorter distances, the PMMA panels should be cut by eliminating cut marks or sharp edges with fine-grained sandpaper (220-600). The cut can be made with a jigsaw with fine toothing (5-10 teeth / cm).

• Material:
  AISI 304 stainless steel (18/10 stainless steel) with a polished finish.




AISI 304 stainless steel polsh	Particular railing

• Installation environment:
  Fontanot Railing Inox20 Wire is the solution for indoor and outdoor use; it is ideal for indoor use. It can also be install outdoors in less aggressive environments recommended in areas not close to the sea and not in presence of harish pollution, please follow all maintenance advice meticulously.
  
  

  Indoor use	Low-aggressive outdoor

• Table of items to be purchased:
  Table of items to be purchased in relation to the length of the railing to be constructed and considering a distance of 1 m between the balusters. For each change of direction purchase 1 extra DA1321 kit.
  
  
• Railing resistance:
  The structural strength can be doubled by halving the distance between the balusters. The structural strength tests to verify compliance with the provisions laid down in Ministerial Decree dated 14/01/2008 and the requirements according to the UNI EN 1991-1-1 (EUROCODE 1) standards have been conducted in Italy at the Giordano Institute laboratories, SIT / SINCERT accredited and authorised by the Ministry for Infrastructures to conduct tests and issue test certificates for the construction materials. The test certificates can be viewed at the link: Railing Certification
  

  Railing resistance



• Cleaning:
  The INOX20 WIRE components are made of 100% AISI 304 stainless steel (18/10 stainless steel); the visible surfaces have been treated to obtain a uniform satin finish. The satin finish makes the surface easily susceptible to attack by corrosive agents, therefore, in seaside environments or areas with heavy atmospheric pollution, as soon as spots start appearing on the railing or handrail, immediately clean the surfaces. Rust spots on the stainless steel do not compromise the structural integrity of the parts; they just become more difficult to remove if not cleaned immediately and left to extend over the surface. Therefore, as soon as spots visible to the naked eye appear, clean them off. Periodic cleaning also needs to be carried out:
  • at least every 12 months in unpolluted suburban or rural areas,
  • at least every 4-6 months in polluted urban areas or close to the sea,
  • whenever solid substances (dust) or liquids deposit on the surfaces.
  For cleaning, use plenty of water and non-abrasive and non-aggressive detergents specifically for stainless steel or metals. After cleaning, dry the surfaces thoroughly with a microfibre cloth to remove the haloes that form because of the limestone in the water. NEVER use abrasive scourers. In the case of “extensive and deep” rust spots, use stainless steel or metal cleaning products generally sold in a pasty or creamy form and rub the oxidised surface in the direction of the satin finish until all the spots have completely been removed. When you have finished cleaning and after perfectly drying all the surfaces, use a soft or microfibre cloth and spread a film of commercial protective oil suitable for stainless steel (silicone oil that can be bought in any hardware shop).